Interfacial microstructure and mechanical properties of TZM alloy and ZrC particle reinforced tungsten composite joint brazed using Ti-61Ni filler

G. H. Han; H. Bian; H. Y. Zhao; X. G. Song; Y. Li; D. Liu; J. Cao; J. C. Feng

doi:10.1016/j.jallcom.2018.02.258

Interfacial microstructure and mechanical properties of TZM alloy and ZrC particle reinforced tungsten composite joint brazed using Ti-61Ni filler

G. H. Han
, H. Bian
, H. Y. Zhao
, X. G. Song^*
, Y. Li
, D. Liu
, J. Cao
, J. C. Feng

^*Corresponding author for this work

Harbin Institute of Technology
Qilu University of Technology

Research output: Contribution to journal › Article › peer-review

30 Scopus citations

Abstract

TZM alloy and ZrC particle reinforced W composite (ZrC_p-W) were vacuum brazed using Ti-61Ni eutectic brazing alloy. The typical interfacial microstructure of the brazed joint consisted of three zones: a Mo solid solution layer, a brazing seam consisting of TiNi phase, TiNi₃ phase and (Ti, Zr)Ni₂ phase, and a diffusion layer composed of W particles, (Ti, Zr)C particles and (Ti, Zr)Ni₂ phase. The results revealed that brazing temperature affected the interfacial morphologies of the joint, the phase constituents of the brazing seam, the element contents of these phases and the mechanical properties of the brazed joint. The optimal shear strengths at room temperature and at 800 °C reached 124.8 MPa and 82.3 MP respectively when brazed at 1240 °C for 10 min. Meanwhile, the fracture paths located at the TZM substrate and the fracture surface exhibited inter-granular fracture characteristics.

Original language	English
Pages (from-to)	266-275
Number of pages	10
Journal	Journal of Alloys and Compounds
Volume	747
DOIs	https://doi.org/10.1016/j.jallcom.2018.02.258
State	Published - 30 May 2018

Keywords

Interfacial microstructure
TZM alloy
Vacuum brazing
ZrC-W composite

Access to Document

10.1016/j.jallcom.2018.02.258

Cite this

@article{9c390904683d442bbc6e6327c9c71f5c,

title = "Interfacial microstructure and mechanical properties of TZM alloy and ZrC particle reinforced tungsten composite joint brazed using Ti-61Ni filler",

abstract = "TZM alloy and ZrC particle reinforced W composite (ZrCp-W) were vacuum brazed using Ti-61Ni eutectic brazing alloy. The typical interfacial microstructure of the brazed joint consisted of three zones: a Mo solid solution layer, a brazing seam consisting of TiNi phase, TiNi3 phase and (Ti, Zr)Ni2 phase, and a diffusion layer composed of W particles, (Ti, Zr)C particles and (Ti, Zr)Ni2 phase. The results revealed that brazing temperature affected the interfacial morphologies of the joint, the phase constituents of the brazing seam, the element contents of these phases and the mechanical properties of the brazed joint. The optimal shear strengths at room temperature and at 800 °C reached 124.8 MPa and 82.3 MP respectively when brazed at 1240 °C for 10 min. Meanwhile, the fracture paths located at the TZM substrate and the fracture surface exhibited inter-granular fracture characteristics.",

keywords = "Interfacial microstructure, TZM alloy, Vacuum brazing, ZrC-W composite",

author = "Han, \{G. H.\} and H. Bian and Zhao, \{H. Y.\} and Song, \{X. G.\} and Y. Li and D. Liu and J. Cao and Feng, \{J. C.\}",

note = "Publisher Copyright: {\textcopyright} 2018 Elsevier B.V.",

year = "2018",

month = may,

day = "30",

doi = "10.1016/j.jallcom.2018.02.258",

language = "英语",

volume = "747",

pages = "266--275",

journal = "Journal of Alloys and Compounds",

issn = "0925-8388",

publisher = "Elsevier B.V.",

}

TY - JOUR

T1 - Interfacial microstructure and mechanical properties of TZM alloy and ZrC particle reinforced tungsten composite joint brazed using Ti-61Ni filler

AU - Han, G. H.

AU - Bian, H.

AU - Zhao, H. Y.

AU - Song, X. G.

AU - Li, Y.

AU - Liu, D.

AU - Cao, J.

AU - Feng, J. C.

PY - 2018/5/30

Y1 - 2018/5/30

N2 - TZM alloy and ZrC particle reinforced W composite (ZrCp-W) were vacuum brazed using Ti-61Ni eutectic brazing alloy. The typical interfacial microstructure of the brazed joint consisted of three zones: a Mo solid solution layer, a brazing seam consisting of TiNi phase, TiNi3 phase and (Ti, Zr)Ni2 phase, and a diffusion layer composed of W particles, (Ti, Zr)C particles and (Ti, Zr)Ni2 phase. The results revealed that brazing temperature affected the interfacial morphologies of the joint, the phase constituents of the brazing seam, the element contents of these phases and the mechanical properties of the brazed joint. The optimal shear strengths at room temperature and at 800 °C reached 124.8 MPa and 82.3 MP respectively when brazed at 1240 °C for 10 min. Meanwhile, the fracture paths located at the TZM substrate and the fracture surface exhibited inter-granular fracture characteristics.

AB - TZM alloy and ZrC particle reinforced W composite (ZrCp-W) were vacuum brazed using Ti-61Ni eutectic brazing alloy. The typical interfacial microstructure of the brazed joint consisted of three zones: a Mo solid solution layer, a brazing seam consisting of TiNi phase, TiNi3 phase and (Ti, Zr)Ni2 phase, and a diffusion layer composed of W particles, (Ti, Zr)C particles and (Ti, Zr)Ni2 phase. The results revealed that brazing temperature affected the interfacial morphologies of the joint, the phase constituents of the brazing seam, the element contents of these phases and the mechanical properties of the brazed joint. The optimal shear strengths at room temperature and at 800 °C reached 124.8 MPa and 82.3 MP respectively when brazed at 1240 °C for 10 min. Meanwhile, the fracture paths located at the TZM substrate and the fracture surface exhibited inter-granular fracture characteristics.

KW - Interfacial microstructure

KW - TZM alloy

KW - Vacuum brazing

KW - ZrC-W composite

UR - https://www.scopus.com/pages/publications/85043351347

U2 - 10.1016/j.jallcom.2018.02.258

DO - 10.1016/j.jallcom.2018.02.258

M3 - 文章

AN - SCOPUS:85043351347

SN - 0925-8388

VL - 747

SP - 266

EP - 275

JO - Journal of Alloys and Compounds

JF - Journal of Alloys and Compounds

ER -

Interfacial microstructure and mechanical properties of TZM alloy and ZrC particle reinforced tungsten composite joint brazed using Ti-61Ni filler

Abstract

Keywords

Access to Document

Other files and links

Fingerprint

Cite this